Additives in Acidizing Fluids

Learning Objectives After completing this topic “Additives in Acidizing Fluids“, you will be able answer to: What is the purpose of using additives in acidizing process for oil well?Which acid is used in acidizing process?What are acid additives?What is iron control agent?How is HCl used in fracking?What is SandStone acidizing?What is in hydrochloric acid?What is stimulation in oil and gas?What is acid job in oil industry?How do you make hydrofluoric acid?What are the objectives of matrix stimulation? By completing this topic and then applying the learnings in your job, you will be able to attain Basic Application Competence Level in Acidizing and Other Chemical Treatments. Corrosion Inhibitors https://youtu.be/4eccv89i6nE Corrosion Inhibitors The principal additives to acidizing fluids are corrosion inhibitors. A corrosion inhibitor is a chemical that slows acid corrosion on drill pipe, tubing, or any other metal that the acid contacts during treatment. Brief explanations follow of the acid corrosion mechanism, types of acid corrosion, and corrosion by different acid types. Acid Corrosion on Steel: All uninhibited acid solutions corrode steel. The attack of acid on steel occurs through the dissociated hydrogen ion of the acid solution. This results in the oxidation and dissolution of iron at the anodic sites on the metal surface along with the reduction of hydrogen ions and formation of hydrogen at the cathodic sites: Anodic Reaction (Oxidation) [latex]\overbrace{\quad Fe \quad}^{\textrm{Metalic iron}} \Rightarrow \overbrace{\quad Fe^{++} \quad }^{\textrm{Ionic iron} } + \overbrace{\quad 2e^{-} \quad }^{\textrm{Electrons} }[/latex] Cathodic Reaction (Reduction) [latex]\overbrace{\quad 2H^+ \quad}^{\textrm{ Ionic hydrogen}} + \overbrace{\quad 2e^- \quad}^{\textrm{Electrons}} \rightarrow \overbrace{\quad H_2 \quad}^{\textrm{Hidrogen}}[/latex] These two reactions can be summarized by the following overall reaction: [latex]\overbrace{\quad Fe \quad}^{\textrm{Metalic iron}} + \overbrace{\quad 2H^+ \quad}^{\textrm{Ionic hydrogen}}\overbrace{\quad Fe^{++} \quad}^{\textrm{Ionic iron}}\overbrace{\quad H_2 \quad}^{\textrm{Hydrogen}}[/latex] This electrochemical corrosion process is shown in Figure 1 (electrochemical corrosion). FIGURE 1 The units of measurement used to determine the amount of corrosion are [latex]\tfrac{lb.}{sq.ft}[/latex] To illustrate, one sq. ft of steel 0.001 in. thick weighs 0.041 lb.; 1.92 ft of 2-[latex]\tfrac{3}{8}[/latex] in. tubing has an inside surface area of one sq. ft. If corrosion weight loss of this 2-[latex]\tfrac{3}{8}[/latex] in. tubing is 0.041 [latex]\tfrac{lb.}{sq.ft}[/latex], then every foot of the string has lost 0.021 lb. and is thinner by 0.001 in. Acceptable corrosion limits are demonstrated in Table 1 (below). The range is from 0.02 to 0.09 [latex]\tfrac{lb.}{sq.ft}[/latex] of metal surface, depending on temperature. Keep in mind, however, that acids corrode more evenly, with less pitting, at higher temperatures. At elevated temperatures, then, more corrosion may be permitted with less chance of forming a hole in the drill pipe or tubing string. A corrosion limit of 0.10 [latex]\tfrac{lb.}{sq.ft}[/latex] may be acceptable with a low pitting index representing 1% metal loss. Furthermore, there is less risk in an initial completion acidizing treatment than on tubing subjected to repeated acidizing. Temp.[latex]ºF[/latex]Corrosion Limit[latex]\tfrac{lb.}{sq.ft}[/latex]2000.02200-2750.05275-3500.09Table 1: Acceptable corrosion limits Since acid corrosion is strongly influenced by the chemical composition of the steel, metal chemistry is an important factor in corrosion studies on oilfield tubular goods. API specifications, however, are based on physical properties of the metal (i.e., tensile strength) rather than chemical composition. Marked differences in chemical composition may exist in the same grade of tubing or casing from different manufacturers, or from lot to lot from the same manufacturer. A general rule to follow when comparing the degree of corrosivity of two types of tubular goods is that the higher the hardness of the metal, the more prone it is to acid attack. This rule is illustrated in Figure 2 (Effect of HCl on different types of steel). FIGURE 2 Remember, however, that there are exceptions to every rule. Types of Acid Corrosion: In uninhibited acid solutions, the corrosion of steel is usually uniform. The constant shifting of anodic and cathodic areas spreads corrosion more or less evenly over the entire surface of the metal. Pitting of the steel surfaces occurs in some situations due to inhibitor breakdown, insufficient inhibitor, and metal impurities. Inhibitor Breakdown: On steel exposed to acid solutions containing an inferior corrosion inhibitor, a pitting type of corrosion is not uncommon. All corrosion inhibitors eventually break down after some period of time, depending on, among other factors, temperature, acid strength, and metal type. When this point is reached, an inferior inhibitor may actually tend to promote pitting by desorbing from the metal surface in localized areas. Insufficient Inhibitor Regardless of the quality of corrosion inhibitor, pitting may also occur if there is an insufficient amount of inhibitor to effectively coat steel surfaces under certain conditions. Unprotected steel surface areas are rapidly attacked by the acid solution, and pitting occurs. Metal Impurities: Another condition that promotes pitting is the presence of impurities or inclusions within the steel itself. For example, small pieces of slag may become trapped during the forming of the steel, or improper heat treating or quenching of the steel may produce discontinuities in its grain structure. These imperfections may, in turn, become anodic to the rest of the surrounding steel structure, and thus promote acid attack. Hydrogen Embrittlement: This is one of the most insidious forms of corrosive attack. Because oxidation and dissolution of iron occur at the anodic sites on the metal surface when steel is corroded by acid, the reduction of hydrogen ions and formation of hydrogen takes place at the cathodic sites. The cathodic reaction can be expressed as [latex]\overbrace{\quad H^+\quad}^{\textrm{Hydrogen ion}} +\ \overbrace{\quad e^- \quad}^{\textrm{Electron}} \ \Rightarrow \overbrace{\quad H \quad}^{\textrm{Atomic hydrogen}}[/latex] [latex]\overbrace{\quad H \quad}^{\textrm{Atomic hydrogen}} + \overbrace{\quad H \quad}^{\textrm{Atomic hydrogen}} \Rightarrow \overbrace{\quad H_2 \quad}^{\textrm{Molecular hydrogen}}[/latex] Because atomic hydrogen is very small, it can penetrate the metal and become lodged in void spaces along metal grain boundaries. Molecular hydrogen is too large to penetrate and lodge in these spaces, and is not a problem at well temperatures. When atomic hydrogen that has penetrated the metal structure comes in contact with another atomic hydrogen atom, the two combine to form molecular hydrogen within the steel structure. When the larger molecule very slowly migrates out, extremely high pressures develop in the void spaces that literally split the metal open. This process is called hydrogen embrittlement. If hydrogen sulfide (H2S) is involved, the splitting phenomenon is known as hydrogen sulfide cracking. H2S tends to slow down the transformation of atomic hydrogen into molecular hydrogen on the metal surface at the cathode. It thus allows greater penetration into the metal which, in turn, increases the probability of high-strength steel cracking. Figure 3, is a photomicrograph of a crack in stressed Pl05 pipe exposed to 15% HCl saturated with H2S. FIGURE 3 This cracking can occur when very little physical corrosion is taking place. Most commercially available corrosion inhibitors are ineffective in controlling cracking of high-strength steels in acid saturated with H2S. As a general rule, steels with a Rockwell "C" hardness of 22 or less are not as likely to experience H2S cracking as steels with greater hardness. Corrosion by Different Acid Types The most common types of acid solutions used in the oil field are HCl, formic, and acetic. The degree of ionization of hydrogen from the acid molecule determines the acid strength, which is directly proportional to its corrosivity on steel. The degree of ionization for these acids is HCl > formic > acetic. HCl, then, is more corrosive on steel than formic, which is more corrosive than acetic. Quite logically, the more aggressive an acid is in its attack on steel, the more difficult it is to inhibit. The mechanism of attack, however, is the same for all three types, as shown below. [latex]\overbrace{\quad 2HCl \quad}^{\textrm{HCl (inorganic) acid}} + \overbrace{\quad Fe \quad}^{\textrm{Iron}} \Rightarrow \overbrace{\quad FeCl_2 \quad}^{\textrm{Iron chloride}} + \overbrace{\quad H_2 \quad}^{\textrm{Hydrogen}}[/latex] [latex]\overbrace{\quad 2HCHO_2 \quad}^{\textrm{Formic (organic) acid}} + \overbrace{\quad Fe \quad}^{\textrm{Iron}} \Rightarrow \overbrace{\quad Fe(CHO_2)_2 \quad}^{\textrm{Iron formate}} + \overbrace{\quad H_2 \quad}^{\textrm{Hydrogen}}[/latex] [latex]\overbrace{\quad 2HC_2H_3O_2 \quad}^{\textrm{Acetic (organic) acid}} + \overbrace{\quad Fe \quad}^{\textrm{Iron}} \Rightarrow \overbrace{\quad Fe(C_2H_3O_2)_2 \quad}^{\textrm{Iron formate}} + \overbrace{\quad H_2 \quad}^{\textrm{Hydrogen}}[/latex] Inhibitor Types There are two basic types of corrosion inhibitors: inorganic and organic. Inorganic Corrosion Inhibitors: This class of inhibitor includes salts of zinc, nickel, copper, arsenic, antimony, and various other metals. Of these, the most widely used are arsenic compounds. When these arsenic compounds are added to an acid solution, they "plate out," or form iron sulfide at cathodic sites of exposed steel surfaces. These plates decrease the rate of hydrogen ion exchange, because iron sulfide acts as a barrier between metal and acid. It is a continuing process in which acid reacts with iron sulfide, rather than metal. Some advantages of inorganic inhibitors are that they: work very effectively at high temperatures for long contact times;cost less than organic inhibitors. Disadvantages of inorganic inhibitors are that they: tend to lose their effectiveness in 17 to 20% HCl and stronger acid solutions;react with H2S(via FeS ions) to form an insoluble precipitate called arsenic sulfide.(In the reservoir this precipitate exists in a gaseous state, but when it enters the wellbore and cools, a plugging solid forms.);poison refinery catalysts, such as platinum;liberate occasionally toxic arsine gas as a by-product of corrosion;resist mixing and safe handling. Organic Corrosion Inhibitors: These inhibitors are composed of polar organic compounds capable of adsorbing onto the metal surface, thereby establishing a protective film that acts as a barrier between the metal and the acid solution. They usually serve as a cathodic polarizer by limiting the hydrogen ion mobility at cathodic sites. Organic inhibitors are composed of rather complex hydrocarbon units with one or more polar groups made of sulfur, oxygen, or nitrogen. Some advantages of organic inhibitors are that they: can be used in the presence of H2S without precipitation of arsenic sulfide, which can plug the wellbore;do not poison refinery catalysts;work effectively in all acid concentrations. Some disadvantages of organic inhibitors are that they: tend toward in-situ degradation - that is, they chemically degrade with time in the presence of an acid solution, and thus do not readily provide long-term protection at temperatures above 220° F.cost more than the inorganic corrosion inhibitors. Table 2 (below) demonstrates effectiveness of organic and inorganic corrosion inhibitors at high temperatures in 15% HCl. The protective time reflects time required for the HCl to remove 0.05 [latex]\tfrac{lb.}{sq.ft}[/latex] of exposed metal area. Table 2: Effectiveness of corrosion inhibitors at high temperatures in 15% HCl. Type Inhibitor Inhibitor Concentration-% Temperature°F Protection Time- hr.* *Time required for 15% HCl to remove 0.05 lb.sq.ft \tfrac{lb.}{sq.ft} exposed metal area. Organic 0.6 200 24 1.0 250 10 2.0 300 2 Inorganic 0.4 200 24 1.2 250 24 2.0 300 12 Do not make the mistake of assuming that twice as much inhibitor provides twice as much protection: the concentration limit varies from one inhibitor to another. The general rule is that a 2% concentration is maximum. Beyond this point, no practical benefit is gained. Remember that the purpose of a corrosion inhibitor is to slow the acid reaction rate on steel. Inhibitors in and of themselves do not prevent corrosion. Listed in Table 3 are some examples of corrosion protection times available at the more common temperatures found in acidizing treatments. Type ofInhibitorInhibitorConcentrationAcidTypeAcidConcentrationTemp.(°F)ProtectionTime*Low Temp.0.10%HCI15%1007 daysLow Temp.0.15%HCI15%1502.5 daysLow Temp.0.50%HCI15%20017 hrsLow Temp.1.00%HCI28%20021 hrsMedium Temp.0.50%HCI15%20028 hrsMedium Temp.0.80%HCI28%20044 hrsOrganic Acid0.30%Acetic10%20090 days* Time required for specified acid to remove 0.05 [latex]\tfrac{lb}{sq.ft}[/latex] of exposed metal area.Table 3: Effectiveness of various organic corrosion inhibitors at common well temperatures. Intensifiers Although these additives cannot be considered inhibitors when used alone, their effectiveness is increased when they are used in conjunction with an organic inhibitor. The commonest intensifiers are potassium iodide, cuprous iodide, and formamide. The addition of these synergistic chemicals to existing organic inhibitor formulations greatly extends the range of their effectiveness, particularly in higher-temperature applications. Surfactants https://youtu.be/XyCpSDbUeNI Surfactants Surfactants, or surface-active agents, lower surface tension by adsorbing at the interface between liquid and gas. Surfactants can also lower interfacial tension by adsorbing at interfaces between two immiscible liquids and changing contact angles by adsorbing at an interface between a liquid and solid. They are commonly used in acidizing (and other completion and workover operations) to demulsify spent acid and oil, reduce interfacial tension, speed cleanup and prevent sludge formation. Surfactants should not be added to treatment fluids without first having a full understanding of their effects on the reservoir oil at downhole conditions. Without this understanding, it is better not to use surfactants at all in the formulation, particularly when the objective is to break or prevent emulsion (Schecter, 1992). Surface tension is a property of liquids that distinguishes them from gases. Liquid molecules exert a mutual attractive force on each other. When this force a combination of van der Waals' forces and electrostatic forces is not balanced, a tension perpendicular to the surface develops. The greater the attractive force of these molecules for one another, the greater the surface tension of the liquid, and the greater the amount of work per unit area required to rupture the liquid surface. This amount of work (surface tension) is specific for each liquid at a definite temperature and is expressed in [latex]\tfrac{dynes}{cm}[/latex]. Interfacial tension is the force in the interface, or boundary layer, between two unlike liquids. This tension results from unbalanced intermolecular forces in the boundary region, is a factor in the formation or breaking of emulsions in the recovery of treating fluids from matrix permeability. In general, surfactants can be divided into four main groups: cationic, anionic, nonionic, and amphoteric. Cationic surfactants are organic chemicals with molecules that ionize upon contacting water. The water-soluble group is positively charged. The positively charged particle, consisting of oil-soluble and water-soluble ends, contains the surface-active portion of the molecule. The active part orients itself at the liquid/air, acid/oil, or liquid/liquid interface. Most cationic surfactants are amine compounds, such as quaternary ammonium chloride: where R represents an oil-soluble group. Anionic surfactants are organic chemicals with molecules that also ionize upon contacting water. But here the negatively charged particle of each ion, consisting of a water-soluble end and an oil-soluble end, is surface active. The anionic surfactant is negatively charged; it is this part that is active in orienting itself at the surface of the liquid, or at the interface between the water and oil. The positively charged particle goes off into solution and has little to do with surface tension. Some examples of anionic surfactants are: sulfates [latex]\qquad[/latex] [latex]\textrm{R-OSO}_{3}^{\ -}[/latex] sulfonates [latex]\qquad[/latex] [latex]\textrm{R-SO}_{3}^{-}[/latex] phosphates [latex]\qquad[/latex] [latex]\textrm{R-OPO}_{3}^{-2}[/latex] phosphonates [latex]\qquad[/latex] [latex]\textrm{R-PO}_{3}^{-2}[/latex] where R represents an oil-soluble group. Of these, the most common anionic surfactants are sulfates and sulfonates. Anionic surfactants are primarily used as nonemulsifying agents, retarding agents, and cleaning agents. Surfactants are organic molecules that do not ionize and therefore remain uncharged. Most nonionic surfactants contain water groups that are polymers of either ethylene oxide or propylene oxide. Some examples of nonionic surfactants are: polyethylene oxide [latex]\qquad[/latex] [latex]RO(CH_2CH_2O)\textrm{x}H[/latex] polypropylene oxide : Nonionic surfactants are primarily used as foaming agents and nonemulsifiers. Amphoteric surfactants are organic molecules with water-soluble groups which can be positively charged, negatively charged, or uncharged. The specific charge depends on system pH level. If the pH is acidic, the amphoteric surfactant takes on cationic properties, or a positive charge. If the pH is in the neutral range, then it takes on nonionic properties, or remains uncharged. If the pH level is basic, the amphoteric takes on anionic negative charge properties. Two examples of amphoteric surfactants are: amine sulfonate [latex]\qquad[/latex] [latex]RNH(CH_2)\textrm{y}SO_3H[/latex] amine phosphate [latex]\qquad[/latex] [latex]RNH(CH_2)\textrm{z}OPO_3H[/latex] Some amphoteric surfactants are used as corrosion inhibitors, foamers, and silt-suspending agents. Properties Affected by Surfactants The main fluid properties affected by surfactants are surface and interfacial tensions, emulsification tendency, wettability, and dispersibility. Surface Tension: Figure 1 illustrates how surfactants lower surface tension. FIGURE 1 Since the water-soluble group exceeds the water solubility of the oil-soluble group, surfactant molecules orient themselves at the air/water interface (surface). The water-soluble group is in water, and the oil-soluble group in the air. This changes the nature of the air/water interface, making it a combination of air, water, and oil. Because oil has a much lower surface tension than water, surface tension of the water surfactant mixture is lower than the surface tension of pure water.Surface tensions of some common liquids are listed in Table 1 (below) LiquidSurface Tension[latex]\tfrac{dynes}{cm}[/latex]Water72.015% HCL72.0Spent 15% HCl76.9Octane21.8Table 1: Surface tension of common liquids. Some surfactants can reduce surface tension of water to about 27 [latex]\tfrac{dynes}{cm}[/latex] when used in relatively low concentrations. One class of surfactants, called fluoro-surfactants, can lower surface tension below 15 [latex]\tfrac{dynes}{cm}[/latex]. Interfacial Tension: Interfacial tension describes the surface energy between two immiscible fluids, such as water and oil. This interface acts like an invisible membrane that prevents the liquids from mixing. The force required to break this molecular film is called interfacial tension. The interfacial tension between kerosene and water is about 49 [latex]\tfrac{dynes}{cm}[/latex]. By the addition of a surfactant, it can be lowered to near zero. Figure 2 (surfactants lower interfacial tension) shows the surfactant being adsorbed at the oil-water interface. FIGURE 2 Again, the water-soluble group adheres to the water, and the oil-soluble group is in the oil phase. The interfacial surface between the two fluids is now a mixture of oil and water, with the interfacial tension being greatly reduced. Even though the surfactant is water soluble, some of it migrates through the interface and enters the oil phase. When interfacial tension is lowered in an acidizing treatment, the water may break up into smaller droplets that pass through the oil and flow out of the well without forming unwanted emulsions. In the case of oil, interfacial tension can be reduced to enable the oil to pass through rock pore spaces with greater ease. Emulsification Tendency: An emulsion is a mixture of two fluids in which fine droplets of one fluid remain suspended in the other. Emulsions may be oil-external or water-external. In the first instance, oil is the external phase with the water droplets dispersed throughout. This is the most common emulsion found in wellbores connected to oil reservoirs. Water-external emulsion has an aqueous external phase with oil droplets distributed throughout. Many crudes contain naturally occurring surfactants that reduce surface tension between oil and formation water and thus promote the development of emulsions. Treatment of the formation with certain surfactants can also lead to the development of emulsions. However, certain surfactants can be used to treat wells with emulsions problems. Wettability Oil and water are immiscible liquids that compete for a place on the formation surface. The questions of which liquid preferentially wets the rock surface is an important factor in acidizing. When the formation surface is completely covered by a film of oil, the formation is termed oil-wet. Conversely, when covered by water, the formation is water-wet. The electrochemical approach usually explains the ability of a surfactant to adsorb at interfaces between liquids and solids and alter the wettability of solids. Most formations are mixtures of sand, clay, limestone, and dolomite. We next consider each of these components. Sand usually has a negative surface charge. When a cationic surfactant is used, the positive water-soluble group is adsorbed by the negative silica particle. This leaves the oil-soluble group to influence wettability. As a result, cationic surfactants generally oil-wet sand. When anionic surfactants are used, the sand and silicate minerals are generally left in their natural water-wet state. Wettability characteristics exhibited by anionic and cat ionic surfactants on a silicate particle are shown in Figure 3 and Figure 4. FIGURE 3 FIGURE 4 Limestone and dolomite usually have a positive surface charge. Since anionic surfactants have a negative charge, the oil-soluble group is usually left to influence wettability. Hence, anionic surfactants tend to oil-wet lime-stone and dolomite formations. Because carbonates do not usually adsorb cationic surfactants, most cationic surfactants leave limestone and dolomite in a natural water-wet condition. Wettability characteristics exhibited by anionic and cationic surfactants on a carbonate particle are illustrated in Figure 5 and Figure 6. FIGURE 5 FIGURE 6 In the case of nonionic surfactants, the wettability of silicates and carbonates depends primarily on the solubility of the material. If the nonionic is oil-soluble, it will tend to oil-wet the silicates. This is because silicates are attracted by hydrogen bonding. Contact angles are used to study wetting of surfactants. Figure 7 and Figure 8 shows how a wetting and nonwetting drop looks on a solid surface. FIGURE 7 By using the proper surfactant, formation wettability can be changed from oil-wet to water-wet, and vice versa. Since oil flows more easily through water-wet formations, selection of the proper surfactant can be an important factor in increasing oil production. FIGURE 8 Figure 9 shows the results of oil flow through oil-wet and water-wet sands. FIGURE 9 As discussed earlier, certain surfactants are used to alter wetting properties of a producing formation. These curves show that oil exhibits better flow rates through water-wet formations. Care should be taken to have the formation in a water-wet condition following an acidizing treatment, which is often not a simple task. In many instances a surfactant may have been added as an emulsion breaker, and it inadvertently acts as an oil wetter. Dispersibility: Surfactants have been developed to inhibit the swelling, migration, and flocculation of clays, even in high ionic strength solutions, such as acids. This is done by using an anionic surfactant which effectively disperses clay particles in acid mud removal solutions and minimizes the formation of aggregates. Since the smaller particles are easier to suspend, the clay is removed more efficiently. Another system for removing drilling mud is an aqueous solution of surfactants and other chemicals that reduces mud viscosity and disperses solids. Retarding Agents These surfactants are designed to slow the reaction time of acid on carbonate formations. Reaction time is the amount of time it takes for acid to spend from its original concentration to a concentration of about 3.2% at conditions of bottomhole temperature and pressure. During matrix or fracture acidizing, or the pumping of large volumes of acid into a carbonate formation, it is sometimes desirable to control the reaction time of the acid. The principal surfactants used as retarding agents are anionic oil-wetting surfactants, usually sulfonates or sulfates. These function by adsorbing onto the carbonate formation and making part of it oil-wet. Where the surfactant adsorbs most, the acid reacts least. Consequently, an uneven surface is etched into the fracture faces. These uneven surfaces prop the fracture upon completion, resulting in an improved fracture permeability and increased oil and gas production. Cores etched under simulated reservoir conditions: Figure 10 (regular 15% HCl) FIGURE 10 and Figure 11 (acid retarded with anionic surfactant) shows this uneven etching of the acid retarded with an anionic surfactant. FIGURE 11 Unfortunately, these additives have proven only marginally beneficial in retarding acid reaction rates in the field, and there use is not generally recommended. Emulsifying Surfactants These types of surfactants form with acid either an oil-external emulsion or an acid-external emulsion. The acid-external emulsion is commonly used with a mixture of an aromatic and acid to form a dispersion. The solvent phase in this blend dissolves organic residues, while the acid reacts with scale to remove deposits on the formation to increase permeability. The high-viscosity oil-external emulsions are more commonly used in fracture acidizing. As the acid spends itself on the formation, the emulsion breaks. The emulsion retards the acid formation reaction by physically preventing acid contact. Suspending Agents All calcareous formations less than 100% carbonate. Thus many insoluble fines are released during acidizing. When the spent acid is removed from the formation, these fines can be left behind to reduce permeability. Two basic types of suspending agents are used in this application. One is a surfactant that adsorbs onto these fines and keeps them in suspension by electrostatic repulsion. The other is a polymer that creates a molecular bridging effect and, by trapping the fines between polymers, keeps fines suspended. Suspending agents are effective when acidizing a carbonate formation that contains HCl-insoluble materials, such as feldspar, quartz, and clays. Antisludging Agents When acid contacts some crude oils, a sludge can form at the acid/oil interface. This usually happens when the crude contains a high percentage of asphaltenes, and is most severe with high-strength acid systems (20% or higher). Once formed, the sludge is very difficult to dissolve into oil again. As a result, it accumulates in the formation and decreases permeability. To combat formation sludge, surfactants, both cationic and anionic, are used to adsorb and provide a continuous layer of protection at the acid/oil interface. Sludge development can also be prevented by lowering acid strength and controlling return rates after an acid treatment. Figure 12 (acid droplet in sludge-forming oil- a skin like precipitate forms around the acid droplet) FIGURE 12 and Figure 13 (acid droplet containing anti-sludge forming oil- no precipitate forms around the acid droplet) illustrate the effectiveness of an antisludging agent. FIGURE 13 Penetrating Agents These surfactants are commonly used in acidizing tight gas reservoirs and in scale-removal treatments. Their main function is to lower surface and interfacial tensions of the acid. This allows the acid to more easily wet the formation rock and oil-wet scales, resulting in a more uniform reaction. Another benefit of lowering the surface tension of the treating fluid is to decrease the fluid's likelihood to form water blocks in the formation, resulting in a faster and more efficient cleanup after acidizing. Most penetrating agents are nonionic surfactants which water-wet both silicates and carbonates. These surfactants effectively lower the surface tension of acid from 72 [latex]\tfrac{dynes}{cm}[/latex] to about 27 [latex]\tfrac{dynes}{cm}[/latex] when used in a concentration of 0.1%. Nonemulsifiers One major problem encountered in acidizing is emulsification of crude oil and acid, or of crude oil and spent acid. This phenomenon may or may not occur in the formation but does occur in the wellbore. There are two fundamental types of emulsion: oil-external and water-external. Oil-external emulsion is commonly encountered in oil wells. It is usually a thick, viscous fluid mixture which can reduce the flow rate of the well by plugging the formation. Addition of proper surfactants to the acid before pumping can prevent formation of an emulsion during the acid treatment. Obviously, the selected surfactant must be compatible with acid, formation fluids, and all other additives in the treatment design. Alcohol Alcohols are ordinarily used in acidizing fluids to remove water blocks, enhance fluid recovery, retard acid reactivity, and decrease water content. Their effectiveness is limited. The most common alcohols used in acidizing are isopropanol and methanol. Their physical and chemical properties are listed in Table 2. PropertiesIsopropanolMethanolSpecific Gravity at 68 °F0.7850.792Flash Point (closed cup) °F53.653.6Solubility in WaterCompletelyCompletelyTable 2: Physical and chemical properties of isopropanol and methanol Isopropanol is normally used at a maximum of 20% by volume. Methanol is used at various concentrations, commonly 30% by volume. In some cases, methanol alone is used to dilute concentrated acid to various acid-treating solutions. Alcohols are used in acidizing fluids for the following reasons: Removal of Water Blocks: One problem which can severely decrease production in producing wells is blockage of the pore spaces by water — commonly known as a water block. Water blocks may form where high capillary forces are present in porous rocks. The most severe water-block problems occur in formations with gas permeabilities less than 120 md. The alcohol in the treating fluid reduces the capillary forces within the reservoir, thus permitting easier removal of the liquid phases.Enhancement of Fluid Recovery: Another problem encountered in treating oil or gas wells is the recovery of treating fluids, especially in gas reservoirs. The high surface tension of water or acid solution hinders their penetration and recovery. Conventional surfactants help somewhat, although they surfactants lose much of their surface activity by adsorption. The addition of alcohol to acid solutions reduces their surface tension. The concentration of alcohol normally used for this purpose is of sufficient quantity that adsorption is not a problem. Alcohol used in acidizing fluids also increases the vaporization rate of the fluid. This, in turn, lowers vapor pressure, allowing for a more rapid desaturation of water from a gas reservoir.Retardation of Acid Reactivity: Alcohol has a retarding effect on acid reactivity. The retardation rate is proportional to the type and percentage of alcohol added.Decrease of Water in Acid: Some formations contain a large amount of water-sensitive clays. To minimize the amount of water contained in acidizing solutions, alcohols are used in place of part or all of the dilution water. The major disadvantages of using alcohol in acidizing fluids are: Effective Concentration: It takes a large amount of alcohol, 20% or more, to provide beneficial effects.Cost: Replacing water with alcohol in the acidizing solution makes the treatment more expensive.Low Flash Point: Both isopropanol and methanol, and even acid solutions containing 20% or more by volume of either, have low flash points.Increase in Corrosiveness: Corrosion tests have shown that alcohol-acid mixtures require a higher concentration of inhibitor than equivalent nonalcohol-acid mixtures.Adverse Reactions: Formation brines with a high concentration of dissolved salt solids can "salt out" in the presence of alcohols. To help prevent the occurrence of this salt precipitation, do not exceed 20% by volume of isopropanol or 50% by volume of methanol in treating solutions.Incompatibility: Some crude oils are incompatible with both methanol and isopropanol. Conduct compatibility tests before acidizing a well with a fluid containing alcohol. Some formation types may be extremely sensitive to aqueous solutions that contain high concentrations of alcohols. In some cases, formations should not be acidized with alcohol-acid solutions. The formation of undesirable methyl chloride is possible with HCl solutions that contain 30% or more methanol at bottomhole temperatures above 200° F. Mutual Solvents A mutual solvent is a material that is soluble in both hydrocarbon and aqueous solutions. It can help to solubilize an aqueous solution into a hydrocarbon solution or vice versa. Common mutual solvents include ethylene glycol monobutyl ether (EGMBE), diethylene glycol monobutyl ether (DEGMBE), modified glycol ethers (MGE), and also alcohol. The use of mutual solvents, particularly EGMBE and MGE, in acid stimulation of a sandstone reservoir is a common practice. Mutual solvents have been used in postflushes because they help to: reduce water saturation from around the wellbore by lowering the surface tension of the water, thus preventing water blockssolubilize a portion of the water into the hydrocarbon phase, thus reducing the amount of irreducible water saturationprovide a water-wet formation, thus maintaining the best relative permeability for oil productionprevent insoluble fines from becoming oil-wetstabilize emulsionsmaintain the needed concentration of surfactants and inhibitors in solution by helping to prevent adsorption of these materials onto the formation Mutual solvents have also been found to reduce the formation damage that can result from using corrosion inhibitors in acid treatments. The normal treating concentration of mutual solvents varies from 2 to 50% by volume, depending on the application. Most sandstone acidizing applications use 10% or less. Iron Sequestering Agents Iron occurs naturally in formation water, and in formation minerals such as siderite, hematite and pyrite. A primary source of iron, of course, is donwhole tubular goods. In solution, iron can exist in two forms: ferrous iron (Fe2+) and ferric iron (Fe3+). Fe3+ is or primary concern in acidizing, because it precipitates as gelatinous iron hydroxide (Fe(OH) 3) at a pH of 2.5 to 3.5. This precipitation can lead top formation damage. When Fe3+is present in the near-wellbore region, an iron sequestrant, or chelating agent, may be added to the treating solution. Table 1 (below) provides information about various sequestering agents, of which EDTA is the most commonly used. Because these agents can themselves damage the formation, they should be used only when pr-job evaluation and testing indicate a tendency for iron hydroxide precipitation during acidizing. Other methods for keeping iron in solution include pH control and the use of oxygen scavengers. pH control is achieved by using a weak acid, such as acetic, which reacts much more slowly than HCl on limestone and other acid-soluble materials. Thus, some of the acid remains in solution, keeping the pH low and inhibiting iron Hydroxide formation. CompoundMaximum Solubility in 1000 gal 15%Amount of Fe+2 Chelated - ppnEDTA (Ethylene Diamine Tetraacetic Acid)671,450Sodium EDTA~250~5,000NTA (Nitrilo Triacetic Acid)42013,790Citric Acid1,796*57,292Table 1: Solubility and iron chelating capability of various chelating agents. *The solubility of citric acid is considerably higher than 1,796 lb. Theoretically, ferric iron in 15% HCl spent on millscale can be chelated with 1,796 lb of citric acid. However, if the acid was only partially spent on magnetite and the remainder spent on a carbonate rock, calcium citrate could precipitate. Oxygen Scavengers: An oxygen scavenger can be used to economically control concentrations of iron up to approximately 5,000 mpl. It functions by two different mechanisms. First, it removes free oxygen from the fluid, and then helps prevent the oxidization of ferrous iron (F3+2)to ferric iron (Fe+3). Then, it acts as a reducing agent and reduces any dissolved ferric iron present to ferrous iron. This helps maintain iron in solution and helps prevent the precipitation of ferric iron. This helps maintain iron in solution and helps prevent the precipitation of ferric iron in solution. The amount of iron that can be reduced with an oxygen scavenger depends upon the quantity of chemical added, but it can be used up if the fluid is aerated before it is pumped. A comparison of the amount of ferric iron that can be retained by the various methods and additives is illustrated in Figure 1 (iron cotnrol acid systems). FIGURE 1 The safest way to help prevent damage to the reservoir from precipitated iron hydroxide is to clean or "pickle" the pipe with acid before acidizing the formation. This acid should contain large quantities of iron-control additives and should be circulated out of the well, not pumped into the formation. In conduction with this treatment, xylene or hydrocarbon phase should be incorporated or used as a preflush to remove pipe dope and varnish that could plug perforations. ( In most instances, pipe dope is not soluble in xylene or normal hydrocarbons.) Fluid Loss Control Agents In fracture acidizing, fluid loss control helps to extend fractures by minimizing leakoff of the treating fluid through the fracture face. Fluid loss control is difficult to obtain with acid solutions on carbonate formations because the acid is reacting on the surface where the fluid loss additive is being deposited. Fluid loss additives often are composed of two agents: an inert, solid particle that bridges at the fracture surface and a gelatinous material that plugs the pores in the solid granular material. Commonly used fluid loss additives are listed in Table 1 . Fluid TypeSolid AdditivesGelatinous AdditivesAqueous padSilica flourGuar Calcium carbonateCellulose Organic polymerPolyacrylamide Inert solid coated with guar type material Hydrocarbon padInert solid coated with organic sulfonate AcidAcid swellable solidGuar Organic resinKaraya Silica flourCellulose Organic polymersPolyacrylamide Polyvinyl alcoholTable 1: Commonly used fluid loss additives. In aqueous pad fluids, a combination of solid additive and polymer is usually selected. When water without a polymer additive is used, an inert solid coated with guar-type material may be chosen. Acid additives include acid-soluble organic polymers that swell and become soft when contacted by acid, thereby giving both solid and gelatinous characteristics. Other additives are similar to those chosen for use in water-base pad fluids. We now focus on matrix fluid loss, fluid loss in natural fractures, fluid loss in wormholes, and viscosity effects. Matrix Fluid Loss: Many carbonates contain little permeability within the matrix of the rock. Because acid is a reactive substance, however, it creates more surface area as it travels during leakoff. It is very important, therefore, to confine the acid to the fracture. Fluid loss additives are usually sufficient to control matrix leakoff. Ideally, they should be either degradable or slowly soluble in the acidizing solution or in produced fluids. Fluid Loss in Natural Fractures: Some limestone formations have unusually high permeability in the form of natural fractures or vugular flow channels. Fluid loss control in this type of formation cannot be achieved with ordinary fluid loss additives. A larger diverting material is usually required to control the fluid lost to natural fractures. Fluid Loss in Wormholes: Fluid lost to the matrix will react and, if lost in a highly reactive part of the formation, may cause wormholes. These are large, highly conductive channels which usually start when a large pore or vug grows at a rate substantially higher than that of smaller pores and receives an increasingly larger amount of the acid as new surface area is created. From a fluid-loss standpoint, wormholes are similar to natural fractures since they require larger particles for control. If little fluid leakoff occurs to the matrix, few wormholes are likely to occur. For a more detailed discussion of wormhole formation and growth, see Economides et al. (1995). Viscosity Effects: The rate of leakoff is directly related to viscosity. A thicker fluid results in less fluid lost to the formation and, therefore, improved fluid efficiency. If efficiency increases, more live acid can be pumped deeper into the formation, thus increasing fracture flow capacity. Viscosifying the acid can be one of the most important steps in providing fluid-loss control in fracture acidizing treatments. Friction Reducers Friction reducers suppress turbulence and reduce friction pressure in fluids flowing through tubular goods. This can either reduce horsepower requirements or increase treating rates. Most friction reducers are long-chain natural or synthetic polymers, but not all of them work effectively in acidizing solutions. Acid breaks down some of these polymers at a very fast rate, thus leaving little, if any, friction-reducing properties. Many different additives are used as friction reducers. Generic classifications of additives for water- and oil-base pad fluids and for acids are listed in Table 1. Fluid TypeGeneric Classification of AdditiveWater based padGuar and HP Guar Polyacrylamide CelluloseOil based padPolyisobutylene Fatty acids Crosslinked organic polymersAcidGuar Gum karaya Polyacrylamide CelluloseTable 1: Friction reducers. Clay Stabilizers Many clay-stabilizing materials have been developed in recent years to combat formation damage caused by clay swelling and migration. These generally are used in conjunction with minimum-salinity fluids such as 2% KCl, 4% NaCl, and 3% NH4Cl. Types of Clay Some clays, like smectite-mixed layer, swell when they contact fresh water or water with low salt concentrations. There are several ways in which water can enter and damage a productive zone. Some of these are: water filtrate from drilling fluid;loss of water from completion or workover fluids;encroachment into the reservoir by water coning;any type of water-base treating fluid. Productivity also decreases when the produced fluid carries the clay fines (colloidal-size clay particles) in suspension to the wellbore. When any type of pore restriction is encountered, the fines bridge off in the pore, thereby plugging the pore and restricting the flow. Radial flow volume of fines increases while the number of pore channels decreases. Some clays with migrating tendencies are illite, kaolinite, and chlorite. Smectite-Mixed Layer: Smectite-mixed layer, a three-layer clay, is composed of two silica tetrahedral sheets with a central octahedral sheet (Figure 1, smectite -mixed layer). FIGURE 1 In the stacking of their mineral sheets, the proximity of two oxygen layers makes for a weak chemical bond that allows water and other polar organic minerals to enter between unit layers and cause the clay to swell. Figure 2 (three layer clay) illustrates the bonding of smectite-mixed layers. The cation exchange sites attract such positive ions as sodium, potassium, calcium, or ammonium. FIGURE 2 Illite: Illite is a clay composed of two silica tetrahedral sheets with a central alumina octahedral sheet (Figure 3). FIGURE 3 Its structure is similar to smectite, except that potassium and oxygen bind the sheets tightly. Hence, this clay does not expand in the presence of water. However, the potassium ions are very susceptible to the leaching action of slightly acidic water. In some cases, the potassium may be removed and replaced by another cation. These altered minerals, called degraded illites, then allow entry of water and will swell as a result. Kaolinite: Kaolinite is composed of one silica tetrahedral sheet and one octahedral sheet (Figure 4). Their tight hydrogen bonding is not susceptible to water entry. Although kaolinite swells very little on contact with fresh water, it is an important component of migrating fines. FIGURE 4 Figure 5 (two layer clay) schematically illustrates a two-layer clay. FIGURE 5 Kaolinite is the principal member of this family of clays. There are few cation exchange sites: 10% of the number for smectite-mixed layer - too few to cause significant swelling. The degree to which a clay will swell depends on the ions the clay has adsorbed, the degree of degradation of the clay, and the amount of substitution in the clay lattice. The amount of swelling of several salts of smectite is shown for various concentrations in Table 1 (below). These data show that certain ions, especially sodium, allow swelling of clays, resulting in formation damage. In Figure 6 (salinity effects on clays), solutions of sodium chloride (NaCl) were flowed through columns of quartz sand containing 4% by weight of various clays. FIGURE 6 These curves show that the higher salinity solutions of NaCl did less damage to the permeability of the columns than the lower salinity and fresh water systems. Salt ConcentrationSodium SmectitePotassium Smectite*Calcium SmectiteDistilled Water332740.4% Chloride Solution14242.0% Chloride Solution3248.5% Chloride Solution22410.0% Chloride Solution223 to 4Table 1: Effect of salt concentration on the swelling of smectite. *Ammonium chloride will perform essentially the same as potassium chloride. The data in Table 1 and Figure 6 show good agreement. Both indicate that low concentrations of salt swell the smectite more severely than do higher salt concentrations. Figure 6 also indicates that the sensitivity of the clays to water swelling is kaolinite < illite < smectite with kaolinite showing the least damage and smectite the most. Clay damage may be caused by both swelling and migration. When these conditions occur in a formation, the damage must be removed to improve production. This is commonly accomplished by acidizing the formation with HCl-HF mixtures. Clay Control Formation damage due to clays must be prevented rather than cured. When clay particles in sandstone reservoirs are rearranged or disturbed in any manner, it is usually impossible to restore the original permeability. X-ray diffraction analysis can easily determine the type and amount of clay in a particular sandstone. These tests indicate which formations warrant a particular minimum-salinity fluid, clay stabilizer, or special completion technique to avoid formation damage. The position of clays in the rock can be quickly determined by the use of dyes that exhibit characteristic colors when absorbed by different types of clays. Where detailed studies are warranted, the scanning electron microscope (SEM) permits direct observation of certain actions on clays. In a virgin formation, the swelling of a clay particle is in equilibrium with the type and concentration of salts in the connate water. Thus, filtered formation water used in workover operations should not disturb this balance. If clean formation water is not available, it is necessary to synthesize an economical substitute. Cat ionic polymers have been developed that can plate out of fresh water, brine, or acid to stabilize clays and minimize damage. These cationic materials do not oil-wet because the exposed polymer prefers water over oil. The cationic ends of the clay stabilizers bind to the clay minerals in the same manner as the sodium Na+, potassium K+, or calcium Ca++ ions bind. This leaves the water-soluble end of the molecule to form a film over the clay minerals to prevent their swelling and migrating. The principal cationic polymers currently available for use in sandstone acidizing include polyquaternary amines (PQA) and polyamines (PA). Polyquaternary Amines (PQA): PQA is a cationic organic polymer used as a clay-stabilizing additive in sandstone acidizing applications and other treatments. It is a clay-stabilizing chemical that can be universally placed out of aqueous solutions and strong acids. Since PQA does not require a shut-in period, it allows faster well cleanup and prevents damage resulting from swelling and/or migration of clay particles and other silicate fines. The chemical action between PQA and clays results in longer stabilized production before migrating and/or swelling silicates begin to redamage the formation. Figure 7 illustrates relative permeability in a Bandera sandstone core without any clay stabilization treatment. FIGURE 7 Notice that after the core was calibrated with 2% KCl and then exposed to fresh water, permeability decreased about 85%. Figure 8 demonstrates relative permeability in a Bandera sandstone core after a clay-stabilization treatment with PQA (polyquaternary amine). FIGURE 8 Following 2% KCl calibration and clay-stabilization treatment, fresh water had only minimal effect on the permeability, decreasing it slightly. Although the PQA concentration needed depends on permeability, the usual maximum is 3% by volume. All fluids containing PQA should be overflushed with a sufficient volume of fluid to ensure that they are displaced to a distance of at least two feet from the wellbore. This results in more fines stabilizing for a given PQA concentration. Polyamines: These are cat ionic polyelectrolytes which stabilize water-sensitive clays against the swelling and migration problems that might occur on contact with aqueous fluids. PA can be used in aqueous preflush and overflush fluids and acids. Bacteria Control Agents Types of Bacteria Bacteria can cause problems in oil-field operations. Even though these bacteria are extremely small (1 to 3 microns), their sheer numbers can cause plugging problems in injection wells. Generally, the worst problems result from the by-products or chemical processes of certain organisms. Some of these problematic bacteria are sulfate-reducing bacteria, slime-forming bacteria, and iron bacteria. Sulfate-reducing Bacteria The bacterium causing the greatest concern to oil producers is the sulfate-reducing organism. This bacterium, an anaerobic organism, needs an oxygen-free atmosphere in order to spread. Under anaerobic conditions, it can produce H2S. This gas can then corrode downhole tubulars, producing iron sulfide (FeS), which is insoluble in water and acts as a plugging agent. Slime-forming Bacteria Other troublesome bacteria are the slime-forming types. Under aerobic conditions, they may produce large slime masses that cause severe plugging problems. These bacteria are usually found where fresh or surface water comes in contact with produced water. Iron Bacteria A very common bacterium that can cause problems is the iron bacterium. This aerobic bacterium has the ability to oxidize water-soluble ferrous ion to a water-insoluble ferric ion in its metabolic processes. Iron bacteria can cause plugging of source well, filters, and surface lines. Bactericides Many chemicals can be used to control the growth of microorganisms. The most common term for chemical agents designed to kill and inhibit the growth of bacteria is bactericide or biocide. Use of a bactericide can reduce or eliminate the severe problem associated with bacteria. Many bactericides, both cationic and nonionic materials, can be used in acidizing solutions. These chemicals are effective at killing bacteria in concentrations from 1 to 2 [latex]\tfrac{gal}{1000\ gal}[/latex]. Assessment Additives in Acidizing Fluids 1. What should be done to a new string of tubing before acidizing a well? A .Circulate acid down the tubing and up the annulus.B .Circulate acid down the annulus and up the tubing.C .Pump acid down the tubing and then reverse circulate it out. ✔ 2. Which iron is considered worse for the formation? A .FerrousB .Ferric ✔ 3. It is necessary to control leak off when acid fracturing. A .True ✔B .False 4. The bacterium causing the greatest concern to oil producers is the sulfate-reducing organism. A .True ✔B .False 5. Before selecting an acid mixture for a simulation treatment, it is important to test the mixture's compatibility with which of these formation fluids: A .Oil and water. ✔B .Oil only.C .Water only. 6. Which of these fluids is typically used in conjunction with clay-stabilizing materials to combat formation damage? A .2% KClB .4% NaClC .3% NH4ClD .(A), (B) and (C) can all be used. ✔ 7. Corrosion inhibitor is added to all acids before pumping into a well. A .True ✔B .False 8. Acid can break down some friction reducers. A .True ✔B .False 9. If left unchecked, ferric iron precipitates out of solution when ___________. A .the pH decreases.B .the pH increases. ✔ Recommended for You Introduction to Acidizing Hydraulic Fracturing Fundamentals Production Logging of Multiphase Flow in Horizontal Wells